How to get rid of the resin in the wood walls?

Видалення смоли з бруса. ФотоThe aroma of fresh sawn wood. The smell of pine trees. Pleasant sensation of forests and nature. Fresh and healthy air. About all that we dream, when building a wooden house. But not everyone knows what the resin is a cause of headache for many happy owners of houses of timber. As we mentioned in the article "What weeping larch?", Pine and larch (especially fresh cut) tend to provide a resin on the surface, which complicates the processing of the wood surface, as a resin sticks to everything it contacts. In addition, the resin dark place. Such unexpected make the selection of gum, carry out additional work on the elimination of the resin. Staining place with the resin is bad, and sometimes a layer of lacquer is not applied at all. Spoiled the look of beautiful polished walls suggests an answer to the question:
How to get rid of the resin on the wood walls?

Here are a few ways to remove stains from the resin of pine and larch.
Removal of the resin is made only after grinding the surface. This is due to the fact that this process takes place only to a depth of 1-2 mm. On subsequent heating, even after the application of paint can make resin.

Means of removing tar from the timber. photoConduct removal of resin by chemical means does not guarantee that later on the cover does not tread resin. Large areas of tread resin cut with a sharp knife, glued wood veneer, or as a filling putty. As the solvent resins are used:
refined petrol or white spirit;
nitro solvent.
These funds are quickly dissolved resin and volatile, but does not affect the type of wood, and, most importantly, leave no signs of treatment. With the help of these tools handle large surface area of ​​the timber. The final purification procedure is ordinary washing with warm water.
To remove the beam from the surface of the resin can be used an alkaline composition. Alkalis are used to remove the resin with large surfaces.

Ammonia - this is one of the most effective tools used to dissolve the resin. Its distinguishing feature - the absence of traces of surface treatment. It is diluted with acetone, applied 2-3 times a resin streaks and resin rubbed with a brush or a brush until the foam is formed. After that, after 20 minutes wash off with water foam.

Of the available tools can be used to remove tar and resin from the surface of the timber of soda and potash solutions. Mixture prepared as follows:

1. 50 g of potassium carbonate and 50 g of soda dissolved in 1 liter of hot water and add 250 ml of acetone;
2. 25 g of caustic soda in 0.5 liters of cold water and 250 ml of acetone.

These solutions are used to remove resin from the surface before treatment, they can not be used in the processing of already coated parts, rather than finished products. It is important to remember that the alkali to remove from the grooves between the crowns is very difficult to log. The remains of coloring coating solution destroys the formation of crystals.

Effective means for removing the resin is a mixture consisting of 25 g of liquid soap or a neutral timber of soap dissolved in 1 liter of hot water. In the resulting solution was added with stirring 50 ml of liquid ammonia. The treatment is best done by any tar bases in hot form. Alkali should be applied by any brushes other than metal brushes. The resulting foam is rubbed over the surface and wash away the remnants of the resin saponified with plenty of water.

To remove the final remnants of alkali remaining in the grooves between the crowns of wash solution of acetic acid in a ratio of 1:50 (acid poured into water and not vice versa). The solution acetic acid is applied with a sponge, hands should be protected by rubber gloves. Then wash the entire surface of the water.

Repeated application of paint only to dry wood.

We hope - these tips will help remove the resin on wooden walls?

Last Updated (Wednesday, 13 June 2012 13:42)

UkrainianRussianEnglish French (Fr)